surface mount ceramic chip capacitors extended values 0603, x7r dielectric, 100 & 200 volts 100 volts ? 12,000 pf - 39,000 pf 200 volts ? 1,200 pf - 10,000 pf table 1 - dimensions - millimeters new product release outline drawings f3272 02/05 eia size code metric size code (ref) l# length w# width thickness b bandwidth s min. separation mounting technique 0603* 1608 1.6 (.063) 0.15 (.006) 0.8 (.032) 0.15 (.006) see table 2 0.35 (.014) 0.15 (.006) 0.7 (.028) solder wave or solder reflow cap values kemet part number capacitance tolerance thickness - mm qty 7? reel qty 13? reel 12,000pf c0603c123(1)1rac j,k,m 0.8 0.1 4,000 10,000 15,000pf c0603c153(1)1rac j,k,m 0.8 0.1 4,000 10,000 18,000pf c0603c183(1)1rac j,k,m 0.8 0.1 4,000 10,000 22,000pf c0603c223(1)1rac j,k,m 0.8 0.1 4,000 10,000 27,000pf c0603c273(1)1rac j,k,m 0.8 0.1 4,000 10,000 33,000pf c0603c333(1)1rac j,k,m 0.8 0.1 4,000 10,000 39,000pf c0603c393(1)1rac j,k,m 0.8 0.1 4,000 10,000 1,200pf c0603c122(1)2rac j,k,m 0.8 0.1 4,000 10,000 1,500pf c0603c152(1)2rac j,k,m 0.8 0.1 4,000 10,000 1,800pf c0603c182(1)2rac j,k,m 0.8 0.1 4,000 10,000 2,200pf c0603c222(1)2rac j,k,m 0.8 0.1 4,000 10,000 2,700pf c0603c272(1)2rac j,k,m 0.8 0.1 4,000 10,000 3,300pf c0603c332(1)2rac j,k,m 0.8 0.1 4,000 10,000 3,900pf c0603c392(1)2rac j,k,m 0.8 0.1 4,000 10,000 4,700pf c0603c472(1)2rac j,k,m 0.8 0.1 4,000 10,000 5,600pf c0603c562(1)2rac j,k,m 0.8 0.1 4,000 10,000 6,800pf c0603c682(1)2rac j,k,m 0.8 0.1 4,000 10,000 8,200pf c0603c822(1)2rac j,k,m 0.8 0.1 4,000 10,000 10,000pf c0603c103(1)2rac j,k,m 0.8 0.1 4,000 10,000 table 2 - ratings & part number listing to complete the kemet part number, insert capacitance tolerance: j - 5%, k - 10% or m 20%.
in general, the information in the kemet surface mount catalog f3102 applies to these capacitors. the information in this bulletin supplements that in the catalog. electrical parameters as detailed in the kemet surface mount catalog f3102 for x7r, with following specific requirements based on room temperature (25c) parameters: ? operating range: -55c to +125c, with no-bias capacitance shift limited to 15% over that range ? insulation resistance (ir) measured after 2 minutes at rated voltage @ 25c: limit is 1000 megohm microfarads or 100 gigohms, whichever is less. ? capacitance and dissipation factor (df) measured at 1khz at 1.0vrms. 25 volts - df limit is 3.5% > 25 volts - df limit is 2.5% . soldering process wave soldering or reflow soldering is acceptable for these chips. marking these chips are normally supplied unmarked. if required, they can be laser marked as an extra cost option. more detail on the marking format is included in our surface mount catalog f3102. ? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 ? (864) 963-6300 ? www.kemet.com
|
